Renaatus Procon Private Limited
Renaatus Procon Private Limited
Coimbatore, Tamil Nadu
GST No. 33AAFCR6372N1ZX
TrustSEAL Verified
Call 0804841239467% Response Rate
SEND EMAIL

Cementitious & Tile Grout

Our range of products include renafix 300s unsanded tile grout and renafix gp cementitious grout.

Renafix 300S Unsanded Tile Grout

Renafix 300S Unsanded Tile Grout
  • Renafix 300S Unsanded Tile Grout
  • Renafix 300S Unsanded Tile Grout
  • Renafix 300S Unsanded Tile Grout
Get Best Quote
Approx. Price: Rs 310 / PacketGet Latest Price
Product Brochure

Product Details:

Minimum Order Quantity50 Packet
BrandRenafix
Packaging TypePacket
Shelf Life12 Months
Pot Life Of Mix60 Minutes
Packaging Size1 Kg
Joint Width5 mm
Final drying time24 Hours at 20 DegreeC and 50% humidity
Water demand350 ml water per Kg
Application temperaturesDo not apply in temperatures below 5 degree C or above 30 degree C

Renafix 300S Unsanded Grout is a polymer modified grout consisting of a carefully prepared blend of Portland cement, Chemical additives, and filters. Designed as a single component, just and portable water.  It is highly suited for grouting porous and absorbent tiles.

Features:
  • Suitable for walls and floors
  • Suitable for interior and exterior use
  • Suitable for intermittently wet and dry conditions
  • Used in kitchens, bathrooms and showers
  • Constraints: Not suitable if grout is required to be chemically-resistant or completely impermeable.

 

Application Methodology:
Surface Preparation:

Before starting to grout remove spacers and debris in grout joints and remove dust and dirt using a wet sponge. Do not leave water standing in joints. Room temperature must be between 4 deg C and 32 deg C. Apply grout release or sealer if necessary.

Mixing:
Use approximately 300 ml of water 10kg of Renafix tile grout powder. Place portable water in a clean mixing container and add grout powder slowly. Mix by hand or with a slow speed mixer to a smooth stiff consistency. Allow slaking for 5-10 minutes and remix.

Application:
Dampen tile surface with water. Spread with a sharp, firm rubber grout float. Work the grout paste into the joints until completely filled. Use diagonal strokes to pack the joints. Ensure that the joint is filled and grout is not just sitting on top (i.e. “bridging the joint”).

Grout Primary Cleaning:
Remove excess grout from the face of the tiles with the edge of the grout float. Hold the float at a 90-degree angle and pull it at a 45-degree angle diagonally across the joints and tile to avoid pulling out the material.

Grout Secondary Cleaning:
Remove remaining grout with a damp sponge (not wet) or a damp towel. Work diagonally to the joints. Allow drying. When the grout joints are firm, polish the surface with a coarse nylon pad or coarse cloth and minimal water.

Joint Width: 1 to 5 mm

Request
Callback
Yes! I am Interested

Renafix GP Cementitious Grout

Renafix GP Cementitious Grout
  • Renafix GP Cementitious Grout
  • Renafix GP Cementitious Grout
  • Renafix GP Cementitious Grout
  • Renafix GP Cementitious Grout
  • Renafix GP Cementitious Grout
  • Renafix GP Cementitious Grout
  • Renafix GP Cementitious Grout
  • Renafix GP Cementitious Grout
  • Renafix GP Cementitious Grout
  • Renafix GP Cementitious Grout
  • Renafix GP Cementitious Grout
  • Renafix GP Cementitious Grout
  • Renafix GP Cementitious Grout
Get Best Quote
Approx. Price: Rs 450 / BagGet Latest Price

Product Details:

Minimum Order Quantity50 Bag
BrandRenafix
Packaging Size25 Kg
FormPowder
Packaging TypeBag
Shelf Life6 months
Country of OriginMade in India
Water Addition0.2%
Tensile Strength3.5 N/mm2 @ 28 days (W/P: 0.18)
Pullout Bond Strength17 N/mm2 @ 7 days & 20 N/mm2 @ 28 days (W/P: 0.18)
Expansion TimeStart: 20 minutes & Finish: 120 minutes
Fresh Wet DensityApproximately 2220 Kg/m3 depending on actual consistency used
Young's Modulus28 kN/mm2 (ASTM C469 - 94)
Dynamic Load ResistanceCondition of sample: undamaged

Renafix GP2 is a ready to use, non-shrink, and natural aggregate factory blended cementitious precision grout for use in general civil engineering works. It provides extended working life and high early and ultimate strengths.

Features:
  • High Strength & Non shrink
  • Consistency & Economical
  • Greater volumes
  • Requires no special mixing equipment
  • No added chloride and Versatile
  • Provides complete non shrink performance

Recommended Use:
  • Prefabricated concrete panels and beams
  • Stanchion base plates and columns
  • Bridge bearing plates
  • Anchor bolts and bars
  • Underpinning
  • Patch repair works

Application:
Surface Preparation:

The substrate should be properly prepared and should be free from contamination, laitance and loose material. All free water ponding should be blown out of the void just before pouring the grout

Mixing:
Renafix GP2 can be mixed to a flowable or trowelable consistency. The quantity of water required to produce a flowable grout from a 25 kg bag is approximately 4.0 litres. Water addition may be affected by temperature conditions on site. Trials are recommended to determine the correct water requirement. Renafix GP2 should be mixed using a suitable mixer. For flowable consistency, use a hand drill and paddle for small works up to two bags at a time and specialize grout mixers for larger volume. Drum type mixers may not provide sufficient mixing efficiency to derive the optimum performance from the grout. The correct volume of water should be added to the mixer followed by the powder. Mixing should continue until the grout has a smooth, lump-free appearance. This will normally be between 3 – 5 minutes after mixing has started. For best results, Renafix GP2 should be used within 30 minutes once mixed.

At 30 deg C place the grout within 20 minutes of mixing to gain the full benefit of the expansion process. Renafix GP2 can be placed in thicknesses up to 100mm in a single pour when used as an underplate grout. For thicker sections, it is necessary to fill out Renafix GP2 with well-graded silt free aggregate to minimize heat build-up, Typically a 10mm aggregate is suitable. 50 – 100% aggregate weight of Renafix GP2 can be added.

As for all cementitious materials, curing is essential to prevent rapid drying out of the grout and shrinkage caused by the water loss. Curing should be affected by accepted methods such as curing compounds, polythene sheet, wet hessian or water ponding. If a shaped shoulder is required, it should be formed before the grout has reached its final set. Carefully remove the formwork.

Renafix GP2 is self-supporting and cut the shape of the shoulder with a trowel. Preferably the shoulder should be cut to a 45° angle to minimize stresses.

Cleaning:
Clean tools and equipment with water before Renafix GP2 has hardened, otherwise mechanical cleaning will be required.

Packaging:
A 25 kg bag of Renafix GP2 when mixed to a flowable consistency (Add 4.0 litres water) will yield 13.2 litres grout. Renafix GP2 is packaged in 25kg moisture resistant bags.

Shelf Life:
Renafix GP2 has a shelf life of approximately 6 months when stored in a cool dry place in unopened packs.

Cautions:
Contains Portland cement, may irritate eyes and skins. Avoid contact with eyes or prolonged contact with skin. In case of contact, flush thoroughly with water.

Do not take internally. Avoid breathing dust. Wear a respirator in dusty areas. Keep out of reach of children.
Request
Callback
Yes! I am Interested
X

Product Videos

Watch More Videos

Explore More Product

View All Product


Reach Us
Veerapandi C (Executive)
Renaatus Procon Private Limited
B. O. S. No. 26, Sri Ram Avenue, 100 Feet Extension
Coimbatore - 638115, Tamil Nadu, India


Call Us


Send E-mail