Renafix Thin Set Wall Tile Adhesive

Product Details:

Other Details:

• Perfect fix for a superior floor

Method of Application:

• Wet the back side of the tile with water.
• Complete immersion of water is not required
• Clean the surface of the tile with clean water immediately after laying with wet sponge
• Add water with Renafix to form a thick paste.
• Renafix tile adhesive need to be spread it on the leveled base mortar
• After applying give the smooth surface on the tile backside.
• Install ready skirting with continuous joint on the applied floor.
• Preferably with the use of rubber squeeze or rubber sheet.
• Do not apply the pointing material all over the surface.
• Clean the surface of the tile with a clean wet sponge, removing the excess pigment on the tile surface.

Product Details:

Renafix Floor Top is a non-metallic floor hardener, which contains specially graded non metallic hard wearing natural aggregates. It is applied as a dry shake over freshly floated concrete to provide a durable, non-slip monolithic floor.

Features:
Long service life:
High abrasion and impact resistance

Extended service life:
Better abrasion resistance than plain concrete

Non- rusting:
Suitable for wet environments

Non-slip:
Improved safety for personnel and forklifts in wet environments.

Dense surface:
Resists oil and grease penetration

Coloured surface:
Can create aesthetically pleasing environment

Easy application at time of placing concrete:
Floor available for full service once concrete is cured.

Application Methodology:
It is recommended that the floor be marked off into bays of known area. Sufficient material should be laid out to meet the required spread rates. Application of Rena Top Hardener can begin when the base concrete has stiffened to the point when light foot traffic leaves an imprint of about 3mm. Any bleed water should by now have evaporated. Renafix Floor Top is applied in two stages.

• The first application is made using 50% to 70% of the total material. Rena Top Hardener is evenly broadcast onto the concrete surface. When the material becomes uniformly dark by the absorption of moisture from the concrete this first application can be floated. Wooden floats or, on large areas, the power trowel with disc may be used. It is important, however, that the surface is not over worked.
• Immediately after floating, the remaining Rena Top Hardener is sprinkled evenly over the surface. Again moisture is absorbed and the surface can be floated in the same way as before. Final finishing of the floor using a power trowel can be carried out when the floor has stiffened sufficiently so that damage will not be caused.

Product Details:

Renafix 222 Thin Set Tile Adhesive is a multi-purpose, polymer modified thin set powder offering vast utility including applications on interior floor & wall as well as limited exterior* floor & wall installations, It is a cementitious thin set powder to be mixed only with water to install various types of tiles & stone on variety of substrates using thin set method of installation.

Other Details:

• Perfect fix for floor and wall

Advantages:

• Single component, just add water
• High strength, polymer modified
• Economical & easy to use
• Bonds to various substrates
• Exceeds EN12004 / ISO13007 for C2TES1 and exceeds ANSI 118.4 classification
• Suited for demanding external application

Suitable Substrates:

• Concrete
• Concrete Masonry Cement Mortar Beds
• Cementitious Plaster and render
• Tile and Stone
• Brick Masonry
• Cement Terrazzo

Working Properties:

• Excellent adhesion
• High bond strength
• Flexible
• Ready to use

Installation:
Surface Preparation:
Surfaces should be structurally sound, clean and free of all dirt, oil, grease, loose peeling paint, laitance, concrete sealers or curing compounds. Dry, dusty concrete slabs or masonry should be dampened and excess water swept off.

Mixing:
Place clean, potable water into a clean pail. Add thin set powder into the pail. Use approximately 5 – 6L of water for 20 kg of powder. Mix by hand or with a slow speed mixer to a smooth, trowel able consistency. Allow adhesive to slake for 5-10 minutes. Adjust consistency if necessary. Remix and apply with the proper sized notched trowel.

Application:
Apply adhesive to the substrate with the flat side of the trowel, pressing firmly to work into surface. Comb on additional adhesive with the notched side. Use the proper sized notched trowel to ensure full bedding of the tile. Spread as much adhesive as can be covered with tile in 10 minutes. Back butter large tiles (> 12”x12”) to provide full bedding and firm support. Place tiles into the wet, sticky adhesive and beat in using a beating block and rubber mallet to embed tile and adjust the level. Check adhesive for complete coverage by periodically removing a tile and inspecting bedding adhesive transfer onto back of the tile. If adhesive is skinned over (not sticky), remove and replace with fresh adhesive. It is recommended to use spacers to create joints between tiles and subsequently fill the joints with Renafix tile grout.

Cleaning:
Clean all tools and application equipment with water immediately after use. Hardened/cured material can only be removed mechanically.

Health & Safety Information:

• During cold weather, protect finished work from traffic until fully cured.
• Contains Portland cement and silica sand. May irritate eyes and skin. Avoid contact with eyes or prolonged contact with skin. In case of contact, flush thoroughly with water.
• Do not take internally. Silica sand may cause cancer or serious lung problems. Avoid breathing dust. Wear a respirator in dusty areas.
• Keep out of reach of children.

Technical Data:

• Shear Bond, Porcelain tile 28 day cure test by ANSI A118.4 – 1999:F-5.2.3: >300 psi(1.8 MPa)
• Shear Bond, Porcelain tile Water Immersion test by ANSI A118.4 – 1999:F-5.2.3: >190 psi(1.5 MPa)
• Compressive Strength test by ANSI A118.4 – 1999:F-6.1 (Modified): >2750 psi(20.1 MPa)

Product Details:

Renafix 211 Thin Set Tile Adhesive is a superior floor thin set powder for applications of tiles and stones on interior floor & exterior floor installations. It is a cementitious thin set powder to be mixed only with water to install various types of tiles & stone on a variety of substrates using the thin set method of installation.

Other Details:

• Perfect fix for a superior floor

Advantages:

• Single component, just add water
• High bond strength
• Economical & easy to use
• Bonds to various substrates
• Exceeds EN12004 & ANSI 118.1

Suitable Substrates:

• Concrete
• Concrete Masonry Cement Mortar Beds
• Cementitious Plaster and Render
• Brick Masonry
• Cement Terrazzo

Installation:
Surface Preparation:
Surfaces should be structurally sound, clean and free of all dirt, oil, grease, loose peeling paint, laitance, concrete sealers or curing compounds. Dry, dusty concrete slabs or masonry should be dampened and excess water swept off.

Mixing:
Place clean, potable water into a clean pail. Add thin set powder into the pail. Use approximately 5 – 6L of water for 20 kg of powder. Mix by hand or with a slow speed mixer to a smooth, trowel able consistency. Allow adhesive to slake for 5-10 minutes. Adjust consistency if necessary. Remix and apply with the proper sized notched trowel.

Application:
Apply adhesive to the substrate with the flat side of the trowel, pressing firmly to work into surface. Comb on additional adhesive with the notched side. Use the proper sized notched trowel to ensure full bedding of the tile. Spread as much adhesive as can be covered with tile in 10 minutes. Back butter large tiles (> 12”x12”) to provide full bedding and firm support. Place tiles into the wet, sticky adhesive and beat in using a beating block and rubber mallet to embed tile and adjust the level. Check adhesive for complete coverage by periodically removing a tile and inspecting bedding adhesive transfer onto back of the tile. If adhesive is skinned over (not sticky), remove and replace with fresh adhesive. It is recommended to use spacers to create joints between tiles and subsequently fill the joints with Renafix tile grout.

Cleaning:
Clean all tools and application equipment with water immediately after use. Hardened/cured material can only be removed mechanically.

Health and Safety Information:

• During cold weather, protect finished work from traffic until fully cured.
• Contains Portland cement and silica sand. May irritate eyes and skin. Avoid contact with eyes or prolonged contact with skin. In case of contact, flush thoroughly with water.
• Do not take internally. Silica sand may cause cancer or serious lung problems. Avoid breathing dust. Wear a respirator in dusty areas.
• Keep out of reach of children.

Technical Data:

• Shear Bond, Porcelain tile 28 day cure test by ANSI A118.4 – 1999:F-5.2.3: >240 psi (1.5 MPa)
• Shear Bond, Porcelain tile Water Immersion test by ANSI A118.4 – 1999:F-5.2.3: >150 psi (1.0 MPa)

Product Details:

Renafix 211 Thin Set Tile Adhesive is a multi-purpose, polymer modified premium floor & wall thin set powder offering vast utility including application of tiles and stones on interior floor & wall installations. It is a cementitious thin set powder to be mixed only with water to install various types of tiles & stone on variety of substrates using thin set method of installation.

Other Details:

• Perfect fix for a superior floor

Advantages:

• Single component, just add water
• Dual use for floor and wall
• High bond strength
• Economical & easy to use
• Increased flexibility
• Bonds to various substrates
• Exceeds EN12004 / ISO13007, ANSI 118.1 – 1999

Suitable Substrates:

• Concrete
• Concrete Masonry Cement Mortar Beds
• Cementitious Plaster and render
• Brick Masonry
• Cement Terrazzo

Installation:
Surface Preparation:
Surfaces should be structurally sound, clean and free of all dirt, oil, grease, loose peeling paint, laitance, concrete sealers or curing compounds. Dry, dusty concrete slabs or masonry should be dampened and excess water swept off.

Mixing:
Place clean, potable water into a clean pail. Add thin set powder into the pail. Use approximately 5 – 6 L of water for 20 kg of powder. Mix by hand or with a slow speed mixer to a smooth, trowel able consistency. Allow adhesive to slake for 5-10 minutes. Adjust consistency if necessary. Remix and apply with the proper sized notched trowel.

Application:
Apply adhesive to the substrate with the flat side of the trowel, pressing firmly to work into surface. Comb on additional adhesive with the notched side. Use the proper sized notched trowel to ensure full bedding of the tile. Spread as much adhesive as can be covered with tile in 10 minutes. Back butter large tiles (> 12”x12”) to provide full bedding and firm support. Place tiles into the wet, sticky adhesive and beat in using a beating block and rubber mallet to embed tile and adjust the level. Check adhesive for complete coverage by periodically removing a tile and inspecting bedding adhesive transfer onto back of the tile. If adhesive is skinned over (not sticky), remove and replace with fresh adhesive. It is recommended to use spacers to create joints between tiles and subsequently fill the joints with Renafix tile grout.

Cleaning:
Clean all tools and application equipment with water immediately after use. Hardened/cured material can only be removed mechanically.

Health & Safety Information:

• During cold weather, protect finished work from traffic until fully cured.
• Contains Portland cement and silica sand. May irritate eyes and skin. Avoid contact with eyes or prolonged contact with skin. In case of contact, flush thoroughly with water.
• Do not take internally. Silica sand may cause cancer or serious lung problems. Avoid breathing dust. Wear a respirator in dusty areas.
• Keep out of reach of children.

Technical Data:

• Shear Bond, Porcelain tile 28 day cure test by ANSI A118.4 – 1999:F-5.2.4: >256 psi(1.5 MPa)
• Shear Bond, Porcelain tile Water Immersion test by ANSI A118.4 – 1999:F-5.2.3 >165 psi(1.1 MPa)
• Compressive Strength test by ANSI A118.4 – 1999:F-6.1 (Modified): >2550 psi(17.5 MPa)

Product Details:

Renafix Cement Mortar is a construction grade mortar mix designed for laying all kind of Brick Masonry. Renafix Cement Mortar mix is a pre-blended, sanded product. Mortar Mix is highly workable and cohesive, with a long board life and it is pre-bagged ready for use and only requires the addition of clean water.

Features:

• Ready to use
• Quick construction
• Excellent workability
• High bond formation
• Flexible/Self healing
• Minimal wastage
• Good Crack resistance

Installation:
Surfaces to receive Mortar Mix should be clean and free of dirt, loose debris, grease, oil, etc., for the best possible bond. Add 7-8 Litres of clean water into 50 kg of Renafix Cement Mortar mix in a container/bowl and mix well until reach to the workable condition. If required add additional water to reach required workability and consistency of wet mortar mix. Apply a full bed of mortar onto the base, approximately 1/2 inch to 3/4 inch (12 mm to 18 mm) thickness. Push downward into the mortar bed and sideways against the previously laid block with a slight twisting motion. Tool the mortar joints when they become thumbprint hard. This will make the mortar joint watertight and provide a neat appearance. Cure the wall with water into two times for 5 -7 days then allow for plastering.

Product Details:

Renafix 300S Unsanded Grout is a polymer modified grout consisting of a carefully prepared blend of Portland cement, Chemical additives, and filters. Designed as a single component, just and portable water.  It is highly suited for grouting porous and absorbent tiles.

Features:

• Suitable for walls and floors
• Suitable for interior and exterior use
• Suitable for intermittently wet and dry conditions
• Used in kitchens, bathrooms and showers
• Constraints: Not suitable if grout is required to be chemically-resistant or completely impermeable.

 

Application Methodology:
Surface Preparation:
Before starting to grout remove spacers and debris in grout joints and remove dust and dirt using a wet sponge. Do not leave water standing in joints. Room temperature must be between 4 deg C and 32 deg C. Apply grout release or sealer if necessary.

Mixing:
Use approximately 300 ml of water 10kg of Renafix tile grout powder. Place portable water in a clean mixing container and add grout powder slowly. Mix by hand or with a slow speed mixer to a smooth stiff consistency. Allow slaking for 5-10 minutes and remix.

Application:
Dampen tile surface with water. Spread with a sharp, firm rubber grout float. Work the grout paste into the joints until completely filled. Use diagonal strokes to pack the joints. Ensure that the joint is filled and grout is not just sitting on top (i.e. “bridging the joint”).

Grout Primary Cleaning:
Remove excess grout from the face of the tiles with the edge of the grout float. Hold the float at a 90-degree angle and pull it at a 45-degree angle diagonally across the joints and tile to avoid pulling out the material.

Grout Secondary Cleaning:
Remove remaining grout with a damp sponge (not wet) or a damp towel. Work diagonally to the joints. Allow drying. When the grout joints are firm, polish the surface with a coarse nylon pad or coarse cloth and minimal water.

Joint Width: 1 to 5 mm

Product Details:

Renafix 211 Thin Set Tile Adhesive is a multi-purpose, polymer modified premium floor & wall thin set powder offering vast utility including application of tiles and stones on interior floor & wall installations. It is a cementitious thin set powder to be mixed only with water to install various types of tiles & stone on variety of substrates using thin set method of installation.

Other Details:

• Perfect fix for a superior floor

Advantages:

• Single component, just add water
• Dual use for floor and wall
• High bond strength
• Economical & easy to use
• Increased flexibility
• Bonds to various substrates
• Exceeds EN12004 / ISO13007, ANSI 118.1 – 1999

Suitable Substrates:

• Concrete
• Concrete Masonry Cement Mortar Beds
• Cementitious Plaster and render
• Brick Masonry
• Cement Terrazzo

Installation:
Surface Preparation:
Surfaces should be structurally sound, clean and free of all dirt, oil, grease, loose peeling paint, laitance, concrete sealers or curing compounds. Dry, dusty concrete slabs or masonry should be dampened and excess water swept off.

Mixing:
Place clean, potable water into a clean pail. Add thin set powder into the pail. Use approximately 5 – 6 L of water for 20 kg of powder. Mix by hand or with a slow speed mixer to a smooth, trowel able consistency. Allow adhesive to slake for 5-10 minutes. Adjust consistency if necessary. Remix and apply with the proper sized notched trowel.

Application:
Apply adhesive to the substrate with the flat side of the trowel, pressing firmly to work into surface. Comb on additional adhesive with the notched side. Use the proper sized notched trowel to ensure full bedding of the tile. Spread as much adhesive as can be covered with tile in 10 minutes. Back butter large tiles (> 12”x12”) to provide full bedding and firm support. Place tiles into the wet, sticky adhesive and beat in using a beating block and rubber mallet to embed tile and adjust the level. Check adhesive for complete coverage by periodically removing a tile and inspecting bedding adhesive transfer onto back of the tile. If adhesive is skinned over (not sticky), remove and replace with fresh adhesive. It is recommended to use spacers to create joints between tiles and subsequently fill the joints with Renafix tile grout.

Cleaning:
Clean all tools and application equipment with water immediately after use. Hardened/cured material can only be removed mechanically.

Health & Safety Information:

• During cold weather, protect finished work from traffic until fully cured.
• Contains Portland cement and silica sand. May irritate eyes and skin. Avoid contact with eyes or prolonged contact with skin. In case of contact, flush thoroughly with water.
• Do not take internally. Silica sand may cause cancer or serious lung problems. Avoid breathing dust. Wear a respirator in dusty areas.
• Keep out of reach of children.

Technical Data:

• Shear Bond, Porcelain tile 28 day cure test by ANSI A118.4 – 1999:F-5.2.4: >256 psi(1.5 MPa)
• Shear Bond, Porcelain tile Water Immersion test by ANSI A118.4 – 1999:F-5.2.3 >165 psi(1.1 MPa)
• Compressive Strength test by ANSI A118.4 – 1999:F-6.1 (Modified): >2550 psi(17.5 MPa)

Product Details:

Renafix 211 Thin Set Tile Adhesive is a multi-purpose, polymer modified premium floor & wall thin set powder offering vast utility including application of tiles and stones on interior floor & wall installations. It is a cementitious thin set powder to be mixed only with water to install various types of tiles & stone on variety of substrates using thin set method of installation.

Other Details:

• Perfect fix for a superior floor

Advantages:

• Single component, just add water
• Dual use for floor and wall
• High bond strength
• Economical & easy to use
• Increased flexibility
• Bonds to various substrates
• Exceeds EN12004 / ISO13007, ANSI 118.1 – 1999

Suitable Substrates:

• Concrete
• Concrete Masonry Cement Mortar Beds
• Cementitious Plaster and render
• Brick Masonry
• Cement Terrazzo

Installation:
Surface Preparation:
Surfaces should be structurally sound, clean and free of all dirt, oil, grease, loose peeling paint, laitance, concrete sealers or curing compounds. Dry, dusty concrete slabs or masonry should be dampened and excess water swept off.

Mixing:
Place clean, potable water into a clean pail. Add thin set powder into the pail. Use approximately 5 – 6 L of water for 20 kg of powder. Mix by hand or with a slow speed mixer to a smooth, trowel able consistency. Allow adhesive to slake for 5-10 minutes. Adjust consistency if necessary. Remix and apply with the proper sized notched trowel.

Application:
Apply adhesive to the substrate with the flat side of the trowel, pressing firmly to work into surface. Comb on additional adhesive with the notched side. Use the proper sized notched trowel to ensure full bedding of the tile. Spread as much adhesive as can be covered with tile in 10 minutes. Back butter large tiles (> 12”x12”) to provide full bedding and firm support. Place tiles into the wet, sticky adhesive and beat in using a beating block and rubber mallet to embed tile and adjust the level. Check adhesive for complete coverage by periodically removing a tile and inspecting bedding adhesive transfer onto back of the tile. If adhesive is skinned over (not sticky), remove and replace with fresh adhesive. It is recommended to use spacers to create joints between tiles and subsequently fill the joints with Renafix tile grout.

Cleaning:
Clean all tools and application equipment with water immediately after use. Hardened/cured material can only be removed mechanically.

Health & Safety Information:

• During cold weather, protect finished work from traffic until fully cured.
• Contains Portland cement and silica sand. May irritate eyes and skin. Avoid contact with eyes or prolonged contact with skin. In case of contact, flush thoroughly with water.
• Do not take internally. Silica sand may cause cancer or serious lung problems. Avoid breathing dust. Wear a respirator in dusty areas.
• Keep out of reach of children.

Technical Data:

• Shear Bond, Porcelain tile 28 day cure test by ANSI A118.4 – 1999:F-5.2.4: >256 psi(1.5 MPa)
• Shear Bond, Porcelain tile Water Immersion test by ANSI A118.4 – 1999:F-5.2.3 >165 psi(1.1 MPa)
• Compressive Strength test by ANSI A118.4 – 1999:F-6.1 (Modified): >2550 psi(17.5 MPa)